#8668 - 02/23/08 09:47 PM
Re: vaccum hose question?
|
Member
|
Registered: 03/07/05
Posts: 5158
Loc: Southern KY
|
|
It controls the interior vacuum parts for your HVAC. Mine hooks to the little 3-piece vacuum port on top of the blower where the brake booster hooks up. I don't know if that's the correct factory position though, since mine didn't come with an L67.
_________________________
'13 Mustang 3.7V6 - MT82 '00 GP SE (L67 Swap, XP, Headers, 3.25") '98 GTP, '01 Bonne
|
Top
|
|
|
|
#8669 - 02/23/08 09:52 PM
Re: vaccum hose question?
|
Member
|
Registered: 01/08/07
Posts: 6026
Loc: Des Moines ,Iowa
|
|
yes it runs to the back of the motor on top by the fuel rails humm any idea on how i should go on fixing that ??
|
Top
|
|
|
|
#8670 - 02/23/08 10:26 PM
Re: vaccum hose question?
|
Member
|
Registered: 04/13/06
Posts: 6709
|
|
No, not right. It does work with HVAC. There is a connecting hose down near the fuse box. My buddy air wasn't flowing through the vents like it should. Sure enough that hose came disconnected.
_________________________
2002
|
Top
|
|
|
|
#8671 - 02/23/08 10:35 PM
Re: vaccum hose question?
|
Member
|
Registered: 03/07/05
Posts: 5158
Loc: Southern KY
|
|
I'm confused now.
_________________________
'13 Mustang 3.7V6 - MT82 '00 GP SE (L67 Swap, XP, Headers, 3.25") '98 GTP, '01 Bonne
|
Top
|
|
|
|
#8672 - 02/23/08 11:45 PM
Re: vaccum hose question?
|
Member
|
Registered: 12/27/06
Posts: 2159
Loc: Waterford, WI
|
|
No, RooK, you're right.
That line runs all the way into the cabin, into the HVAC controller.
It (de)pressurizes the system that the electric controls adjest for your vents and stuff.
Not sure where it connects on a stock L67 though.
But whatever you do, make sure you hook it to a vacuum-only port, meaning on the throttle-body side of the rotors.
I think it's a bad idea to push boost through that thing.
|
Top
|
|
|
|
#8673 - 02/24/08 12:00 PM
Re: vaccum hose question?
|
Member
|
Registered: 04/13/06
Posts: 6709
|
|
I don't know if that's the correct factory position though, since mine didn't come with an L67. This is why I posted "No, not right" Sorry for the confussion.
_________________________
2002
|
Top
|
|
|
|
#8674 - 02/24/08 03:50 PM
Re: vaccum hose question?
|
Member
|
Registered: 01/09/08
Posts: 415
Loc: CT
|
|
wait, so on my car no matter what setting i put the vents on it comes out of everywhere. is that the same problem??
_________________________
1998 GP GTP K&N ram air intake, v1.0 pcm, 3" DP, stainless steel Borla cat back, 8.8 wires, 104 spark plugs, 180* T-stat, MPS 3.5, F-body brake kit, KYB AGXs on SSCs, anti pogos, front sway bar and strut tower bar, rear sway bar, solid trans/bottom engine mount, short dog bones w/ poly mounts, alt rewire, rebuilt tranny, pioneer stereo
|
Top
|
|
|
|
#8675 - 02/24/08 04:18 PM
Re: vaccum hose question?
|
Member
|
Registered: 01/08/07
Posts: 6026
Loc: Des Moines ,Iowa
|
|
well how should i fix this problem ??
|
Top
|
|
|
|
#8677 - 02/24/08 07:31 PM
Re: vaccum hose question?
|
Member
|
Registered: 01/08/07
Posts: 6026
Loc: Des Moines ,Iowa
|
|
yes its broken thats why i was wondering what it did and ways i can fix it some things that i thought about was sticking some heat shrink around it and then sealing it because i have some layen around or i will go look for some hose to fix it up
|
Top
|
|
|
|
#8678 - 02/24/08 10:51 PM
Re: vaccum hose question?
|
Member
|
Registered: 04/18/05
Posts: 8901
Loc: Bradenton, FL
|
|
cant hurt to try it.
ed morad would probably have one for cheap
_________________________
Corey Smith
|
Top
|
|
|
|
#8679 - 02/24/08 11:44 PM
Re: vaccum hose question?
|
Member
|
Registered: 03/07/05
Posts: 5158
Loc: Southern KY
|
|
Just buy vacuum line that is a tight fit over it and use it as a 'splice.'
_________________________
'13 Mustang 3.7V6 - MT82 '00 GP SE (L67 Swap, XP, Headers, 3.25") '98 GTP, '01 Bonne
|
Top
|
|
|
|
#8680 - 02/25/08 12:04 AM
Re: vaccum hose question?
|
Member
|
Registered: 06/12/06
Posts: 2694
Loc: Alexandria, Virginia
|
|
Originally posted by 4drgt: what is this hose or tube what is it used for i was cleaning my car today and i saw that it was broken and i just want to know if its bad or not You just wanted to show off your engine bay
_________________________
Exterior- stock painted black wheels, clear corners, stainless steel grill, cross and drilled front and rear rotors with evolution brake pads. Coming soon- 18 inch black mustang bullet rims, GT/GTP rear bumper, tinted windows.
|
Top
|
|
|
|
#8681 - 02/25/08 04:35 AM
Re: vaccum hose question?
|
Member
|
Registered: 01/08/07
Posts: 6026
Loc: Des Moines ,Iowa
|
|
note that bay isnt even mine ... i didnt have my camera so i took this picture from online
|
Top
|
|
|
|
|
|