#56984 - 05/20/02 08:15 AM
badges and CAI
|
Junior Member
|
Registered: 05/07/02
Posts: 10
Loc: Over here
|
|
how do u guys take ok the gp badges? and do u guys eye ball it to put it back or do u mark the place where they came off? Also does any1 have pics on replacing the stock air filter and housing?
|
Top
|
|
|
|
#56985 - 05/20/02 08:47 AM
Re: badges and CAI
|
Member
|
Registered: 05/01/02
Posts: 311
Loc: Washington, DC
|
|
The best thing to do to remove the badges is to heat them up with a blow dryer (to soften the glue) or let it sit out in the sun. Then use a thin knife or screwdriver and slowly pry it off, starting at the edges and working your way around.
You can take measurements in case you want to put them back on first if you like, but thtas up to you.
Good luck.
_________________________
Regards,
Chew
2007 Sly Silver Pontiac Solstice GXP
|
Top
|
|
|
|
#56986 - 05/20/02 08:55 AM
Re: badges and CAI
|
Junior Member
|
Registered: 05/08/02
Posts: 10
Loc: Mission, KS
|
|
I would be very careful using a screwdriver or knife to take off the badges. Try dental floss, it will take a while, but it works. You may also need WD-40 or gasoline to clean the goo left over. Just be sure to wipe it off immediately after and then re wax/Zaino the area. Good luck.
_________________________
Brent I. Adams '98 Silvermist GTP Coupe Poly bushings, Thrasher airbox, tranny cooler, 3.4" pulley, U-bend replaced, F-bar, Blazertech 2200's, Crossover wrap, Rat heat shield, Borla tips, Taylor wires, NGK TR55's, stereo stuff
|
Top
|
|
|
|
#56987 - 05/20/02 11:27 AM
Re: badges and CAI
|
Member
|
Registered: 05/01/02
Posts: 55
Loc: Delaware County, PA
|
|
If you go to the grandprixstore and look for the Trasher CAI system, they have detailed intructions there, and pictures too. Its in the under the hood section.
_________________________
Chris Jarrett 99 Black GTP 14.35@ 95 Fully Loaded Reflective Badges Everywhere, S.S. Grilles, Thrasher CAI, Painted Calipers, 180 T-stat, titanium tint,Blazertech 3200's, ASP 3.4 Chinny's Rims
|
Top
|
|
|
|
#56988 - 05/20/02 11:30 AM
Re: badges and CAI
|
Member
|
Registered: 05/01/02
Posts: 55
Loc: Delaware County, PA
|
|
Depending on if you are changing the grandprix for the GTP on the trunk, I actually measured the GTP badge, found the center point, and lined it up to the keyhole in the trunk. Just some suggestions.
_________________________
Chris Jarrett 99 Black GTP 14.35@ 95 Fully Loaded Reflective Badges Everywhere, S.S. Grilles, Thrasher CAI, Painted Calipers, 180 T-stat, titanium tint,Blazertech 3200's, ASP 3.4 Chinny's Rims
|
Top
|
|
|
|
#56989 - 05/20/02 05:59 PM
Re: badges and CAI
|
Junior Member
|
Registered: 05/02/02
Posts: 13
Loc: NEW YORK!
|
|
use a hair dryer and some fishing line. as for the intake do what he said
_________________________
front+rear strut tower bars, 17" enkei RS6, 235/45/17 kumho escta supra tires, de-badged, custom vinyl work, custom painted front grills, reflective lettering PONTIAC, all red bulbs in interior, painted red clipers, removed u-bend+resonator,painted calipers and rotors, de-pinstriped thats all i can think of right now
|
Top
|
|
|
|
#56990 - 05/22/02 02:06 PM
Re: badges and CAI
|
Member
|
Registered: 05/05/02
Posts: 65
Loc: Louisville
|
|
Why would you want to remove your badges in the first place?
_________________________
-Phil C. Black 2000 GrandPrix GT
|
Top
|
|
|
|
|
|