#99987 - 07/26/10 03:20 PM
anyone know how to remove the white plastic clip that bolts the fender to the bumper?
|
Member
|
Registered: 08/09/09
Posts: 90
Loc: Milford, CT
|
|
just like the title says.. i cant figure it out for my life.
|
|
Top
|
|
|
|
|
#99988 - 07/26/10 03:42 PM
Re: anyone know how to remove the white plastic clip that bolts the fender to the bumper?
|
Member
|
Registered: 04/13/09
Posts: 81
Loc: Eagan
|
|
take a flat head screw driver and put it between the bumper and te clip then get a pliers and move it back and forth it should do the trick... had to remover mine to put in my grille
_________________________
|
|
Top
|
|
|
|
|
#99989 - 07/27/10 07:12 AM
Re: anyone know how to remove the white plastic clip that bolts the fender to the bumper?
|
Member
|
Registered: 01/09/08
Posts: 415
Loc: CT
|
|
did mine over the winter, its aPITA little triangle looking thing. i found that the easist way was to pull the bumper but you can do it without pulling it. you have to turn the whole fender and line it up trhu the hole
_________________________
1998 GP GTP K&N ram air intake, v1.0 pcm, 3" DP, stainless steel Borla cat back, 8.8 wires, 104 spark plugs, 180* T-stat, MPS 3.5, F-body brake kit, KYB AGXs on SSCs, anti pogos, front sway bar and strut tower bar, rear sway bar, solid trans/bottom engine mount, short dog bones w/ poly mounts, alt rewire, rebuilt tranny, pioneer stereo 
|
|
Top
|
|
|
|
|
#99990 - 07/27/10 09:22 AM
Re: anyone know how to remove the white plastic clip that bolts the fender to the bumper?
|
Member
|
Registered: 08/09/09
Posts: 90
Loc: Milford, CT
|
|
well i tried doing the screw driver and ended up snapping the piece in half. then i was just trying to pull it apart and all i had to do was pull the bumper forward and it slid right off. so i glued the piece back together and its sitting as is right now...
|
|
Top
|
|
|
|
|
#99991 - 07/27/10 10:19 AM
Re: anyone know how to remove the white plastic clip that bolts the fender to the bumper?
|
Member
|
Registered: 01/09/08
Posts: 415
Loc: CT
|
|
is it loose on there? id give it a few shakes before trusting that glue down the road
_________________________
1998 GP GTP K&N ram air intake, v1.0 pcm, 3" DP, stainless steel Borla cat back, 8.8 wires, 104 spark plugs, 180* T-stat, MPS 3.5, F-body brake kit, KYB AGXs on SSCs, anti pogos, front sway bar and strut tower bar, rear sway bar, solid trans/bottom engine mount, short dog bones w/ poly mounts, alt rewire, rebuilt tranny, pioneer stereo
|
|
Top
|
|
|
|
|
#99992 - 07/27/10 10:41 AM
Re: anyone know how to remove the white plastic clip that bolts the fender to the bumper?
|
Member
|
Registered: 08/09/09
Posts: 90
Loc: Milford, CT
|
|
idk yet it seems pretty secure but i cant make a judgement yet because the fender isnt even seated flush with the bumper (fender is all dented up) if worst comes to worst ill just go to a yard and pocket a new clip, of course with how bad ive seen ppl smash gp's in ct id be lucky if they are even still attatched to the car
|
|
Top
|
|
|
|
|
#99993 - 07/27/10 11:15 AM
Re: anyone know how to remove the white plastic clip that bolts the fender to the bumper?
|
Member
|
Registered: 01/09/08
Posts: 415
Loc: CT
|
|
go to chuck and eddies, i had to get a fender there and got the clip with it but threw the old one out
_________________________
1998 GP GTP K&N ram air intake, v1.0 pcm, 3" DP, stainless steel Borla cat back, 8.8 wires, 104 spark plugs, 180* T-stat, MPS 3.5, F-body brake kit, KYB AGXs on SSCs, anti pogos, front sway bar and strut tower bar, rear sway bar, solid trans/bottom engine mount, short dog bones w/ poly mounts, alt rewire, rebuilt tranny, pioneer stereo
|
|
Top
|
|
|
|
|
#99994 - 07/27/10 03:38 PM
Re: anyone know how to remove the white plastic clip that bolts the fender to the bumper?
|
Member
|
Registered: 08/09/09
Posts: 90
Loc: Milford, CT
|
|
i went there about a month ago looking for a fender, they had 3 97-03 gp's all with destroyed right side fenders. but worth another shot
|
|
Top
|
|
|
|
|
|
Previous Topic
Index