How do you do this? Something about pulling a tan and blue wire from the passenger fuse box?
detailed help would be great!

pull a fuse inside the driverside fuse box, just a small fuse, look in your owners manaul to see which fuse to pull.

I'm pretty sure the fuse pull doesn't work on 02+ cars. I know that it has something to do with some wires but I'm not sure on the specifics. Wait for Blackarrow or someone to come around, they should know.

its just behind the panel you take off of the dash on the drivers side...

that was a terrible way to explain it... let me try again

When you open your door its the small panel on the side of the dash. There is a plug that you pull out of it, its towards the firewall, i believe.

It's practically right there when you take the little panel off. There's a huge heat sink attached to the module too.

Those both arent making sense :-/

here
http://macgp.clubgp.com/howto/appearance/drl/drl.htm

Hey 4drgt, does that work for a 02 gp as well.

Does this works for a 02 gp as well

Yes, it should.

This method worked on my 02 just fine. Best advice for you is to be patient -- that heat sink does not like to be disconnected so don't get angry and rip it out. Work at it carefully until you get it to willingly pull off.

That was by far the most frustrating thing ive done in a long time.
Theres NO WAY IN HELL that thing was coming off. I worked at it for like 20 minutes. that harness was gonna rip off.
I STILL couldnt get it off in fear that i would rip the whole thing out.
Apparently im missing a step or something because that car will fall apart before that stupid harness comes off.
Maybe its because its so cold out here?
Is there any way to make that harness come out easier?
Any advice would be great because im just having a terrible time with this.

Iirc I went up through the bottom and used a screwdriver. It did take some finagling but I got mine off.

whered you put the screwdriver to yank it off?
i tried everything and failed

Iirc the clip/s are on the side and I went from the bottom (tore my arm up a bit)and used the screwdriver to pry the clip out of the way to slide the connector off.

I already tore my arm up and didnt get it off haha

i thought that was the biggest PITA ever... i couldnt get it for like 15 minutes... u just gotta have like three arms so they can hold the clips open and one to remove

Man, it was a PITA to get off. My hands were bleeding and that thing did not want to come off for nothing, so I went a got some plyers and yanked it out, but I think I pulled it all out and the seat went back to its normal position I guess which scared the hell out of me. But after like 25 minutes everything was working good and now I can put some aftermarket lights in there now since I don't have the DRL's, thanks everybody that responded to the post.

Is there a latch somewhere holding it in?! Or something i might be missing? Or is it strictly just plugged in tight as hell? Because i swear im this close [ ] to ripping that sucker out.

It has the standard plastic clips that most electrical connectors have.

I dont know what those clips look like, or how to disconnect them. I just have no idea. This is the biggest pima. Is it that blue flat part? I could use some insight.

really need some help on this. what/where are the plastic clibs. all instructions i found dont mention it even having any.

yea, its that blue plastic clip thats holding it together but to get to it better, go from under the dash and push the brake down for better access to it. But when i took the blue clip out, I damage it a little but i won't need it now anyways. Also my lights are a bit brighter a night since I don't have the DRL's, woo hooo.

Alright, im getting bits and peices of advice, now i know its the blue clip, are there any other clips holding the harness in? I still cant get the thing out. How do you get the clip out? mine wont move in any direction, and i cant figure out how that thing is in there.

It's been a couple of years for me since I was in there last so I gave all I could.

I cant figure out how that clip comes out/ how its removed. Its eating at me too that i cant get it off, im holding back from ripping it off so much haha

Here's a pic of the connector:


Looks like the black pronged part holds it on to me..

I really need someone to come through with some answers on this. Ive seen that picture and the write up, but it just blatently says something like "disconnect from heat sink". and thats it. I'm looking for the HOW part. haha

i did this for my 98 GTP. instead of just unplugging it i wired a switch. i can have them on or off whenever i want..

Try compressing the black pronged part towards the connector with a small screwdriver, then wiggle the connector out.

we have. numerous times.

man up and pull the thing off.

haha i got it off before you said that but thanks. it was apparently already broken, and horrible tried to be fixed

I was laughing so hard when I read that!

I think I found a smilie for that...