#69112 - 01/07/07 01:15 AM
New ZZP SS ic, high pitched ring?? not belts!
|
Member
|
Registered: 10/15/06
Posts: 31
Loc: Edmonton
|
|
Installed everything, car started no leaks, no rocker noise, except high pitched ringing. Disappears on RPM increase and when the engine gets warm. ( still the odd ring).
high pitched Rings at Idle. I installed rockers 1.84, 3.25 pulley, 3 inch down pipe, PCM, new plugs 180 t stat, Throttle body HV and SS inter cooler.
I think its the two plates?
_________________________
SD hood, air dam, as of Jan 10th 2006, 3.25 pulley, SS ic, 1.84 rockers, 3" DP, t stat, plugs, PCM 1.0 and "shocked look on face"
|
Top
|
|
|
|
#69113 - 01/07/07 02:11 AM
Re: New ZZP SS ic, high pitched ring?? not belts!
|
Member
|
Registered: 05/01/02
Posts: 2126
Loc: Portland Or.
|
|
If it only does it when cold, try cleaning the IAC valve... That's the valve that makes the noise that people complain about making a sucking sound at idle when the car is cold.
|
Top
|
|
|
|
#69114 - 01/07/07 10:13 AM
Re: New ZZP SS ic, high pitched ring?? not belts!
|
Member
|
Registered: 05/02/04
Posts: 188
Loc: MASS.
|
|
check your gaskets around the intake and intercooler.i had same promblem bad gasket made a high pitch sound,take a soap and water solution in spray bottle and spray around the intercooler.if it goes away you have a gasket leak.i used the gm gaskets when installed intercooler bad mistake!!i hope this helps
99 gtp coupe
|
Top
|
|
|
|
#69115 - 01/07/07 04:39 PM
Re: New ZZP SS ic, high pitched ring?? not belts!
|
Member
|
Registered: 03/07/05
Posts: 5158
Loc: Southern KY
|
|
You can spray carb cleaner or starting fluid around it to find any leaks as well. You'll hear the engine rpms go up if there is a leak.
_________________________
'13 Mustang 3.7V6 - MT82 '00 GP SE (L67 Swap, XP, Headers, 3.25") '98 GTP, '01 Bonne
|
Top
|
|
|
|
#69116 - 01/07/07 04:43 PM
Re: New ZZP SS ic, high pitched ring?? not belts!
|
Member
|
Registered: 04/18/05
Posts: 8901
Loc: Bradenton, FL
|
|
are you sure thats not the sound of you S/C? It will probably be a lot louder now
_________________________
Corey Smith
|
Top
|
|
|
|
#69117 - 01/07/07 05:11 PM
Re: New ZZP SS ic, high pitched ring?? not belts!
|
Member
|
Registered: 10/15/06
Posts: 31
Loc: Edmonton
|
|
As Aaron suggested I used soapy water. It appears that it is being suck in at the rear right side by the snout. I will also apply what Rook suggested in 5 minutes. The seal look fine when install, any takes on that one?
Can I drive the car safely until I fix it?
_________________________
SD hood, air dam, as of Jan 10th 2006, 3.25 pulley, SS ic, 1.84 rockers, 3" DP, t stat, plugs, PCM 1.0 and "shocked look on face"
|
Top
|
|
|
|
#69118 - 01/07/07 05:26 PM
Re: New ZZP SS ic, high pitched ring?? not belts!
|
Member
|
Registered: 10/15/06
Posts: 31
Loc: Edmonton
|
|
Contact..I sprayed carb stuff, engine reacted. Thank you one and all. Hopefuly tommorrow "I get her done..."
_________________________
SD hood, air dam, as of Jan 10th 2006, 3.25 pulley, SS ic, 1.84 rockers, 3" DP, t stat, plugs, PCM 1.0 and "shocked look on face"
|
Top
|
|
|
|
#69119 - 01/07/07 05:45 PM
Re: New ZZP SS ic, high pitched ring?? not belts!
|
Member
|
Registered: 05/01/02
Posts: 2126
Loc: Portland Or.
|
|
Way to go!!!
Good luck with the repair!!
|
Top
|
|
|
|
#69120 - 01/07/07 08:44 PM
Re: New ZZP SS ic, high pitched ring?? not belts!
|
Member
|
Registered: 05/02/04
Posts: 188
Loc: MASS.
|
|
that is totaly wierd my leak was in the same exact spot!!makes me wonder??
99 gtp
|
Top
|
|
|
|
#69121 - 01/07/07 10:16 PM
Re: New ZZP SS ic, high pitched ring?? not belts!
|
Member
|
Registered: 10/15/06
Posts: 31
Loc: Edmonton
|
|
And you used the GM gasket and I used the ZZP ones? Now I am not sure what to use...but the closes gasket is in town. I am going to take a long hard look in that area. Sounds like a question for the forum. I am going to use a GM gasket, hopefully they have one in town. Man does that car haul, the black marks must of been 20 feet long... The sound disappears when the car warms up so I hope with the hole plugged the black marks on the pavement will get longer.
_________________________
SD hood, air dam, as of Jan 10th 2006, 3.25 pulley, SS ic, 1.84 rockers, 3" DP, t stat, plugs, PCM 1.0 and "shocked look on face"
|
Top
|
|
|
|
#69122 - 01/07/07 10:56 PM
Re: New ZZP SS ic, high pitched ring?? not belts!
|
Member
|
Registered: 03/07/05
Posts: 5158
Loc: Southern KY
|
|
When you get some new gaskets, try using some of that Permatex copper gasket spray. You just spray the gasket prior to installation and it helps fill the crevices. Might assist in getting a nice seal.
_________________________
'13 Mustang 3.7V6 - MT82 '00 GP SE (L67 Swap, XP, Headers, 3.25") '98 GTP, '01 Bonne
|
Top
|
|
|
|
#69123 - 01/07/07 10:58 PM
Re: New ZZP SS ic, high pitched ring?? not belts!
|
Member
|
Registered: 09/17/04
Posts: 113
Loc: shelby twp, mi
|
|
would that spray work with my valve cover gaskets?
_________________________
just when i think you cant get any dumber...
|
Top
|
|
|
|
#69124 - 01/08/07 12:31 AM
Re: New ZZP SS ic, high pitched ring?? not belts!
|
Member
|
Registered: 03/07/05
Posts: 5158
Loc: Southern KY
|
|
The spray is mainly for metal/stiff paper gaskets to help fill voids and create a better seal. Head gaskets are an example of a good use. Using it on cork or rubber doesn't really help anything since they swell/compress naturally. Best thing for those is proper torque and a clean mating surface.
_________________________
'13 Mustang 3.7V6 - MT82 '00 GP SE (L67 Swap, XP, Headers, 3.25") '98 GTP, '01 Bonne
|
Top
|
|
|
|
#69126 - 01/08/07 11:23 AM
Re: New ZZP SS ic, high pitched ring?? not belts!
|
Member
|
Registered: 10/15/06
Posts: 31
Loc: Edmonton
|
|
No I dont think so Herc, we followed the instructions. alternated sides like a tire. The guy that helped me with the work is a good lic Mech. We took 3 times longer than we should of, just to make sure things went right. And every new piece we put in (except sc leak) is running very well. Perhaps me and Aaron just happen to get that type of gasket.
_________________________
SD hood, air dam, as of Jan 10th 2006, 3.25 pulley, SS ic, 1.84 rockers, 3" DP, t stat, plugs, PCM 1.0 and "shocked look on face"
|
Top
|
|
|
|
|
|