#69128 - 01/08/07 04:28 PM
Re: New ZZP SS ic, high pitched ring?? not belts!
|
Member
|
Registered: 10/15/06
Posts: 31
Loc: Edmonton
|
|
I used new ZZP gasket and Aaron used GM Gaskets. Any how.....more work..
_________________________
SD hood, air dam, as of Jan 10th 2006, 3.25 pulley, SS ic, 1.84 rockers, 3" DP, t stat, plugs, PCM 1.0 and "shocked look on face"
|
Top
|
|
|
|
#69129 - 01/08/07 04:32 PM
Re: New ZZP SS ic, high pitched ring?? not belts!
|
Member
|
Registered: 05/02/04
Posts: 188
Loc: MASS.
|
|
i hope it is not a flaw in their machine work !!
99 gtp coupe
|
Top
|
|
|
|
#69130 - 01/08/07 10:05 PM
Re: New ZZP SS ic, high pitched ring?? not belts!
|
Member
|
Registered: 10/15/06
Posts: 31
Loc: Edmonton
|
|
ZZP replied that I should use RTV and that should seal it. Rook suggested I use gasket spray and I will.
I don't want to take it apart a third time.
_________________________
SD hood, air dam, as of Jan 10th 2006, 3.25 pulley, SS ic, 1.84 rockers, 3" DP, t stat, plugs, PCM 1.0 and "shocked look on face"
|
Top
|
|
|
|
#69131 - 01/09/07 12:03 AM
Re: New ZZP SS ic, high pitched ring?? not belts!
|
Member
|
Registered: 12/29/05
Posts: 724
Loc: Dallas, Tx
|
|
Good luck with the repair dude...I wanna see what this car can do though...hit us up w/ some numbers once everything is working properly.
_________________________
---Kevin
|
Top
|
|
|
|
#69132 - 01/09/07 12:20 AM
Re: New ZZP SS ic, high pitched ring?? not belts!
|
Member
|
Registered: 10/15/06
Posts: 31
Loc: Edmonton
|
|
I already had to cancel first Dyno run...before the leak got big, the tires would burn rubber for a long way....... any how back to work....
_________________________
SD hood, air dam, as of Jan 10th 2006, 3.25 pulley, SS ic, 1.84 rockers, 3" DP, t stat, plugs, PCM 1.0 and "shocked look on face"
|
Top
|
|
|
|
#69133 - 01/11/07 01:19 AM
Re: New ZZP SS ic, high pitched ring?? not belts!
|
Member
|
Registered: 10/15/06
Posts: 31
Loc: Edmonton
|
|
Car is repaired. When installing a gasket on the supercharger look very closely at the end where the supercharger snout is. You will see there is very little room for error. My gasket was only on at that point by 1/8 th of an inch even though the bolt holes where lined up and the rest of the gasket matched fine. There is room for at least 3/8 of an inch. This problem was reported with two different makes of gaskets. I have pictures not to sure how to post them.
_________________________
SD hood, air dam, as of Jan 10th 2006, 3.25 pulley, SS ic, 1.84 rockers, 3" DP, t stat, plugs, PCM 1.0 and "shocked look on face"
|
Top
|
|
|
|
#69134 - 01/11/07 01:23 AM
Re: New ZZP SS ic, high pitched ring?? not belts!
|
Member
|
Registered: 08/09/03
Posts: 3256
Loc: Oregon
|
|
To post a photo, go to photobucket and upload it there (it's free). That will give you a web address to view the photos.
Come back here, and type (IMG)www.website for your photo.com(/img)
But instead of the () brackets, use []
|
Top
|
|
|
|
#69135 - 01/11/07 11:18 AM
Re: New ZZP SS ic, high pitched ring?? not belts!
|
Member
|
Registered: 10/15/06
Posts: 31
Loc: Edmonton
|
|
_________________________
SD hood, air dam, as of Jan 10th 2006, 3.25 pulley, SS ic, 1.84 rockers, 3" DP, t stat, plugs, PCM 1.0 and "shocked look on face"
|
Top
|
|
|
|
#69136 - 01/11/07 11:23 AM
Re: New ZZP SS ic, high pitched ring?? not belts!
|
Member
|
Registered: 10/15/06
Posts: 31
Loc: Edmonton
|
|
A good gasket on the bottom (black) Pontiac. Seems to be missing the notch cut out.
_________________________
SD hood, air dam, as of Jan 10th 2006, 3.25 pulley, SS ic, 1.84 rockers, 3" DP, t stat, plugs, PCM 1.0 and "shocked look on face"
|
Top
|
|
|
|
|
|