#77148 - 03/22/09 11:10 PM
Rear strut mounting plate ?
|
Member
|
Registered: 11/08/08
Posts: 2689
Loc: Eagan,MN
|
|
well i have the spring compessed but the nut on the top just keeps spinning with the shaft inside the rubber boot.
suggestions ?? im in no hurry, but i have about 40 hours from now to return the compressors lol for all my money
_________________________
|
|
Top
|
|
|
|
|
#77149 - 03/22/09 11:17 PM
Re: Rear strut mounting plate ?
|
Member
|
Registered: 03/04/07
Posts: 375
Loc: so. indiana
|
|
doesnt the top have a spot for a allen head?
_________________________
 03 slp-fwi-udp-gmpp-aeroforce
|
|
Top
|
|
|
|
|
#77150 - 03/22/09 11:23 PM
Re: Rear strut mounting plate ?
|
Member
|
Registered: 04/13/06
Posts: 6709
|
|
May have to use big allen to hold it and turn the nut.
_________________________
 2002
|
|
Top
|
|
|
|
|
#77151 - 03/23/09 12:27 AM
Re: Rear strut mounting plate ?
|
Member
|
Registered: 02/08/04
Posts: 3463
Loc: Gonzales Tx.
|
|
Just use vise grips on the shaft to hold and turn the nut off.
|
|
Top
|
|
|
|
|
#77152 - 03/23/09 11:12 AM
Re: Rear strut mounting plate ?
|
Member
|
Registered: 11/08/08
Posts: 2689
Loc: Eagan,MN
|
|
Originally posted by Chico:
Just use vise grips on the shaft to hold and turn the nut off. the shaft is round, so vice grips = fail
_________________________
|
|
Top
|
|
|
|
|
#77153 - 03/23/09 11:31 AM
Re: Rear strut mounting plate ?
|
Member
|
Registered: 01/01/08
Posts: 3900
Loc: Ontario, Canada
|
|
Originally posted by jorgs_7:
the shaft is round, so vice grips = fail then you may need to use that allen head and wrench. I never had this issue and my nuts were all rusty. 
|
|
Top
|
|
|
|
|
#77154 - 03/23/09 11:36 AM
Re: Rear strut mounting plate ?
|
Member
|
Registered: 11/08/08
Posts: 2689
Loc: Eagan,MN
|
|
yea, the removal was pretty easy. luckily the 2 bolts at the knuckle were the same size as my socket i use for my rims. that was lucky, but other wise i had to do a few tool runs.
_________________________
|
|
Top
|
|
|
|
|
#77155 - 03/23/09 12:31 PM
Re: Rear strut mounting plate ?
|
Member
|
Registered: 02/07/09
Posts: 332
Loc: mass
|
|
if it is the old strut use a air gun and angle it with the nut. like with the socket and gun straight up, pull back on the gun making an angle and wot on the gun.
_________________________
99 3.8 Firebird 5 spd/99 gp gt,zzp pcm, HAI, STB, 2.5Dp to 2.5 dynomax custom exhaust 
|
|
Top
|
|
|
|
|
#77156 - 03/23/09 12:39 PM
Re: Rear strut mounting plate ?
|
Member
|
Registered: 02/07/09
Posts: 332
Loc: mass
|
|
if u can get the boot out of the way, vice the shaft and have it get stuck on the coil, then air gun the heck out of it.
_________________________
99 3.8 Firebird 5 spd/99 gp gt,zzp pcm, HAI, STB, 2.5Dp to 2.5 dynomax custom exhaust
|
|
Top
|
|
|
|
|
#77157 - 03/23/09 12:46 PM
Re: Rear strut mounting plate ?
|
Member
|
Registered: 11/08/08
Posts: 2689
Loc: Eagan,MN
|
|
1. dont have an air gun.
2. this sucks.
3. i have to go buy more tools
_________________________
|
|
Top
|
|
|
|
|
#77158 - 03/23/09 12:58 PM
Re: Rear strut mounting plate ?
|
Member
|
Registered: 02/07/09
Posts: 332
Loc: mass
|
|
if u think about it an air gun is good if u got the compressor. but i wouldnt buy all that if dont have any air tools/equiptment. if worst comes to it have a local shop do it or if u know some 1 that has the tools.
_________________________
99 3.8 Firebird 5 spd/99 gp gt,zzp pcm, HAI, STB, 2.5Dp to 2.5 dynomax custom exhaust
|
|
Top
|
|
|
|
|
#77159 - 03/23/09 02:43 PM
Re: Rear strut mounting plate ?
|
Member
|
Registered: 11/08/08
Posts: 2689
Loc: Eagan,MN
|
|
its ok i got it !
_________________________
|
|
Top
|
|
|
|
|
#77161 - 03/23/09 06:52 PM
Re: Rear strut mounting plate ?
|
Member
|
Registered: 05/23/03
Posts: 8078
Loc: Austin, TX
|
|
Try using a bigger hammer.
_________________________
Bobby
Died 5/1/08, resurrected 5/15/08
ASCD SD hood, 17" Bullitts, Overkill PCM, 3.4" Pulley, NGK TR55IX, K&N 9" cone filter, JimmyC D/P, U-bend removed, Flowmaster 40 series, Hooker big bore tips with resonators, S/B brake lines, drilled/slot rotors, GMPP handling kit, KYB struts, F&R strut supports, HID's, LED's, 2.5" Air Dam, red GTP overlays on custom badges, white rear insert.
|
|
Top
|
|
|
|
|
#77162 - 03/23/09 06:57 PM
Re: Rear strut mounting plate ?
|
Member
|
Registered: 04/18/05
Posts: 8901
Loc: Bradenton, FL
|
|
Originally posted by jorgs_7: Originally posted by Chico:
[b] Just use vise grips on the shaft to hold and turn the nut off. You=fail. How can you not put vice grips on it? Because it is circular? Sounds like you need to learn how to use vice grips. An allen head will work just as well as the vice grips.
_________________________
Corey Smith 
|
|
Top
|
|
|
|
|
|
Previous Topic
Index